How to Remove a CPU From a Motherboard

There are times when you may have to remove a CPU if you wish to take apart a computer. If you cannot move the lever, you will need to take action in another way. For example, your motherboard and processor could be placed in a vice, but this could pose a danger if it slips.

You can open locked CPUs in several different ways. However, one method requires the use of a special tool, which costs between $10 and $100. Unfortunately, most people cannot afford it because it is quite expensive. Fortunately, this article will explain how to store them without damaging either one.

Before Removing Your CPU

Before you connect your new computer to your old one, you will need to remove your CPU. A paper towel should be used to wipe off any old thermal compound that may have collected on the bottom of the chip. As a result, heat cannot be transferred from the chip to the heatsink, which will be damaged.

You should avoid touching bare metal on your computer since this can cause it to stop working. In addition, the wrist strap that you should use should not be static. For more information on safety precautions, you can read this article if you are unsure how to do this.

Here are the steps for removing a CPU from a motherboard:

Remove the cards from the case by opening them and taking them out. In addition, it is recommended that you remove your video card, sound card, modem card, network card, Firewire/USB adapter, and any other add-ons you have installed.

You will need to lift one side of the metal frame that holds the heatsink and fan if you want to remove them. To do so, use your fingers or a screwdriver to lift the side.

It is a good idea to remove the part that keeps your computer cool. It is very easy to do this by lifting the piece of furniture with your fingers or with the help of a screwdriver more detail Big Tech Review. It is important to keep lifting it until you can pull it away from the computer’s motherboard.

The heatsink is a piece of metal usually attached to the top of your computer to keep it from getting too hot. If you are going to touch that piece of material under the corner of the CPU, please make sure you do not touch it.

Four screws hold down your motherboard. Remove them. If you are using a screw or nut, there usually are different types, so be sure you are using the right one. It’s okay if you are unable to remove the screw or nut. You can always get a screwdriver or nut driver to help you out to make this task easier.

A paper towel or cotton swab can be used for cleaning thermal compounds. First, you need to wipe them completely off and then let them dry to see any streaks left behind; you should only let the copper part of the heatsink be bare. To do this, you should keep repeating the process until no streaks are left.

Apply a new line of thermal compound. As a best practice, it is recommended that it be applied width-wise, although it can also be applied length-wise. There should be a line on the bottom of your heatsink that is about half an inch wide, thicker than a grain of rice. Make sure that all compounds are used; otherwise, this will not work.

I would recommend that you replace the screws holding your motherboard in place. Then, put the motherboard back in its original location after replacing the screws. It is then necessary to tighten the studs so that only your hand can move them, but not too tight.

The motherboard should be installed with the heatsink and fan. Using your fingers or a screwdriver, push down on the motherboard. Start with the four corners of the motherboard and then continue to the next section; to ensure that everything lines up correctly, make sure that all the pins have been pushed into their original holes.

The motherboard will need to be connected to the cables that have been attached to it. You will find them between the keyboard and monitor of your computer at the rear of the computer.

Put the new motherboard in the previously occupied slot by the old motherboard. Slide the case through carefully until the top or bottom of the compartment is flush with the top. Next, you should turn on your computer, close it, and make sure it is plugged incorrectly by What PC Build. If you notice that your computer is turning off at random, there is a possibility that you have a defective heatsink. Many of our customers had this problem fixed by replacing their heatsinks.

Try plugging in your computer and turning it on to see if it works. If you did that and it worked, then all left is to remove the software from the computer. I think the cables on the computer or inside the computer might be causing the computer not to work. Please ensure that everything is correctly connected to the computer and that there are no exposed pins inside the computer.

I wish you success in your endeavors! Hopefully, now you will be able to use your computer at the same speed as before. If you use a few simple tools, you can eliminate unnecessary stuttering and frame-dropping issues. Please share this information with your friends and family.

Conclusion

The following is a step-by-step guide to removing a CPU from a motherboard. All of the steps can be completed in a short amount of time and are very straightforward. As long as you have the right tools, you will not have any problem disassembling your computer.

It will not take long for you to find out what to do once you know what you need to do. Feel free to contact us with any questions or concerns that you may have. Let us know what you need.